As an Amazon Associate I earn from qualifying purchases.
Peachtree Woodworking Supply #ad - Zero clearance inserts can be used in conjunction with most any table saw blade including thin kerf, standard kerf and carbide tipped blades. Zero clearance inserts help prevent tear out by essentially enveloping the blade on all sides which doesn’t allow the wood to tear out since there is not gap between the blade and insert.
We recommend that you use separate zero clearance inserts for dado blades since the gap for dados will be much wider than standard width table saw blades. If you own a table saw, then you probably have had smaller pieces of wood get caught between the saw blade and the factory supplied throat plate opening.
The insert features two snug Fit sand-able side tabs that allow you to remove a little material at a time for a perfect fit if necessary. The reason you would use zero clearance inserts with dado blades is to reduce the amount of tear out the dado blade set produces. This can cause that piece of wood to jam up against the blade and go flying across the room or worse yet, right back at you. This is especially true when cutting plywood. Zero clearances help minimize this situation from happening since there is no gap between the blade and the zero clearance opening.
Fulton #ad - Includes leveling screws, side and end adjustment screws;pre-cut blade bottom pocket. Small jet, grizzly, Powermatic 64 insert will fitvarious models of table saws. Insert dimensions: 12-1/2” x 3-9/16” x 7/16” - jt-164 jet/Powermatic 64A Zero-Clearance Table Saw Insert.
POWERTEC #ad - Includes: 1 dado insert for Ridgid R4512 Table Saw. Function: serves as a premium replacement for Ridgid R4512 dado throat plate item # 080035003093. Design features: this solid iron insert flaunts optimal flatness for a leveled application without the hassle of making constant adjustments, plus it’s constructed with a smooth, gloss finish that makes it easier to feed and slide your wood across onto the saw.
Removable: possesses a built-in a finger hole conveniently located away from the blade, allowing you to safely lift up, pull out and detach the insert when needed.
This is especially true when cutting plywood. Also be aware of the shape of your current insert of whether its round, we recommend that you measure the exact length, square ends or if there are any indents or protruding notches. Zero clearances help minimize this situation from happening since there is no gap between the blade and the zero clearance opening.
The opening is more like a custom slot cut to the exact width of your table saw blade. Zero clearance inserts help prevent tear out by essentially enveloping the blade on all sides which doesn’t allow the wood to tear out since there is not gap between the blade and insert. Insert colors may vary from images shown. Another great reason to use a zero clearance insert is to help reduce that pesky and irritating tear out you always tend to get on your cuts.
Elimantes dangerous gap around blade where thin off-cuts can get wedged.
1. Peachtree Woodworking
#adNEW GRIZZLY/SHOP FOX TABLE SAW ZERO CLEARANCE INSERT by Peachtree Woodworking PW945
#adPeachtree Woodworking #ad - 13 5/16" x 3 11/16" - made of UHMW. Helps to prevent tear-out plus close the large factory gap. Grizzly-g1023-sl & g1023-slx - shop fox w1677 & W 1711. The insert is blank so you can custom fit the blade slot by passing your blade through it.More information #ad
| Brand | Peachtree Woodworking #ad |
| Manufacturer | Peachtree Woodworking #ad |
| Part Number | PW945 |
More information #ad
2. Peachtree Woodworking Supply
#adPhenolic Zero Clearance Insert for Delta Uni-Saw Contractor | Large Grizzly and Other Table Saws with a 13-3/8” x 3-3/4” x 1/2” Throat Plate Opening
#adWe recommend that you use separate zero clearance inserts for dado blades since the gap for dados will be much wider than standard width table saw blades. If you own a table saw, then you probably have had smaller pieces of wood get caught between the saw blade and the factory supplied throat plate opening.
More information #ad
You can also use zero clearance inserts with dado blade sets. Since every table saw brand and manufacturer is different, width and thickness of your table saw insert or opening and compare it to the size we list. The opening is more like a custom slot cut to the exact width of your table saw blade. The insert features two snug Fit sand-able side tabs that allow you to remove a little material at a time for a perfect fit if necessary. The reason you would use zero clearance inserts with dado blades is to reduce the amount of tear out the dado blade set produces. This can cause that piece of wood to jam up against the blade and go flying across the room or worse yet, right back at you. This is especially true when cutting plywood. Zero clearances help minimize this situation from happening since there is no gap between the blade and the zero clearance opening.
| Brand | Peachtree Woodworking Supply #ad |
| Manufacturer | Fulton #ad |
| Weight | 1.23 Pounds |
| Part Number | AMZ-4133 |
| Model | 4133 |
More information #ad
3. Grizzly
#adGrizzly Industrial H4231, Zero Clearance Table Saw Insert for G1023RL & SL Series
#adGrizzly #ad - Sized to fit grizzly g1023sl and g1023slx table saws. Special phenolic composition out-lasts and out-performs wood foam and plastic supports work right up to the blade sized to fit grizzly g1023sl and. Supports work right up to the blade.More information #ad
| Brand | Grizzly #ad |
| Manufacturer | Grizzly #ad |
| Height | 0.5 Inches |
| Length | 3.7 Inches |
| Weight | 1.15 Pounds |
| Width | 13.4 Inches |
| Part Number | H4231 |
| Model | H4231 |
More information #ad
4. Fulton
#adJet,Grizzly,Power Matic 64 Zero Clearance Insert for Table Saws
#adMore information #ad
Made from high-density phenolic laminate with a bonded-melamine surface. Please check your Length x Width x Thickness of your current insert before ordering.| Brand | Fulton #ad |
| Manufacturer | Fulton #ad |
| Part Number | AMZ-4134 |
| Model | AMZ-4134 |
More information #ad
5. Leecraft
#adLeecraft Craftsman 21833 Table Saw Zero-Clearance Insert CR-4
#adLeecraft #ad - Installation instructions included. Precision machined from melamine faced high density phenolic laminate. Leecraft model number CR-4. 15-1/8" x 4" x 1/8" thick with pre-milled blade, dado and riving knife slot. Fits craftsman 21833, grizzly g0715p, dayton 4KXD1, Masterforce 240-0036 table saws.More information #ad
| Brand | Leecraft #ad |
| Manufacturer | Leecraft #ad |
| Height | 1.05 Inches |
| Length | 15.15 Inches |
| Weight | 1.24 Pounds |
| Width | 4.2 Inches |
| Part Number | 21833 |
More information #ad
6. POWERTEC
#adPOWERTEC 71420 Table Saw Dado Insert Compatible with Ridgid R4512 10 inch Cast Iron Table Saw
#adRemovable: possesses a built-in a finger hole conveniently located away from the blade, allowing you to safely lift up, pull out and detach the insert when needed.
More information #ad
Secure placement: comes with non-countersunk adjustment holes designed to provide perfect alignment, and is held in place by a tab that clips the back of the plate to the table, preventing your table saw throat plate from popping up while in use.| Brand | POWERTEC #ad |
| Manufacturer | POWERTEC #ad |
| Height | 0.81 Inches |
| Length | 15.81 Inches |
| Width | 4.44 Inches |
| Part Number | 71420 |
| Model | 71420 |
More information #ad
7. Leecraft
#adLeecraft DW-2 Zero-Clearance Table Saw Insert for DeWalt Model DW744 and DW746
#adLeecraft #ad - Constructed of high-density phenolic laminate with a bonded-melamine surface. Significantly reduces saw noise, chip-out, dust, and splintering.More information #ad
Table saw insert for eWalt DW744 and DW746. Measures 13-5/8-by-3-3/4 inches LxW. User-friendly with leveling and lateral adjustment screws, rear anti-life pin, and precut blade bottom pocket.| Brand | Leecraft #ad |
| Manufacturer | Leecraft #ad |
| Height | 13.85 Inches |
| Length | 4.35 Inches |
| Weight | 1.2 Pounds |
| Width | 13.85 Inches |
| Part Number | DW-2 |
| Model | DW-2 |
More information #ad
8. Fulton
#adSmall Grizzly, Jet, Powermatic 64 Table Saw Zero Clearance Insert by Peachtree Woodworking PW956 Approx Dims 12-1/2 in x 3-1/2 in x 7/16 in
#adFulton #ad - Zero clearance inserts can be used in conjunction with most any table saw blade including thin kerf, standard kerf and carbide tipped blades. We recommend that you use separate zero clearance inserts for dado blades since the gap for dados will be much wider than standard width table saw blades.This is especially true when cutting plywood. Also be aware of the shape of your current insert of whether its round, we recommend that you measure the exact length, square ends or if there are any indents or protruding notches. Zero clearances help minimize this situation from happening since there is no gap between the blade and the zero clearance opening.
More information #ad
You can also use zero clearance inserts with dado blade sets. The reason you would use zero clearance inserts with dado blades is to reduce the amount of tear out the dado blade set produces. 12-1/2" x 3-1/2" x 7/16" thick - made of uhmw please check your Length, Width and Thickness of your current insert before ordering. The opening is more like a custom slot cut to the exact width of your table saw blade. Zero clearance inserts help prevent tear out by essentially enveloping the blade on all sides which doesn’t allow the wood to tear out since there is not gap between the blade and insert. Insert colors may vary from images shown. Another great reason to use a zero clearance insert is to help reduce that pesky and irritating tear out you always tend to get on your cuts.
| Brand | Fulton #ad |
| Manufacturer | Peachtree Woodworking Supply Inc. #ad |
| Part Number | PW956 |
More information #ad
9. Leecraft
#adLeecraft DL-1U Zero Clearance Table Saw Insert for Delta Table Saw Colors may Vary
#adLeecraft #ad - Fits: delta: unisaw & left-tilt unisaw, grizzly g1023, 10" tilt arbor saw, steel city 35605, sears craftsman 22104, 35675, jet ctas-10, "hybrid" & left-tilt contractor, 22114, 10" Contractor, 35680, 35610, 35670, bridgewood bw10ts, powermatic 63, 22124, 35685.Elimantes dangerous gap around blade where thin off-cuts can get wedged.
More information #ad
Offers superior rigidity, durability, flatness, and low friction; reduces chip-out and splintering. Measures: 13-3/8" x 3-3/4" x 1/2" Please measure before ordering. Includes leveling screws, side and end adjustment screws; rear safety pin; precut blade bottom pocket for fully retracted blades and bevel cuts.| Brand | Leecraft #ad |
| Manufacturer | Leecraft #ad |
| Height | 3 Inches |
| Length | 8 Inches |
| Width | 3 Inches |
| Part Number | DL-1U |
| Model | DL-1U |
More information #ad
10. Peachtree Woodworking Supply
#adDelta UHMW Zero Clearance Table Saw Insert Approx Dims 13-3/8in x 3-3/4in x 1/2in
#adPeachtree Woodworking Supply #ad - Please check your Length, Width and Thickness of your current insert before ordering. Insert comes with leveling screws and rear safety pin. The insert is blank so you can custom fit the blade slot for standard Kerf, Thin Kerf or Dado blades.More information #ad
13 3/8" x 3 3/4" x 1/2" thick- made of UHMW. Helps to prevent tear-out and closes the large factory gap between blade and insert.| Brand | Peachtree Woodworking Supply #ad |
| Manufacturer | Peachtree Woodworking Supply Inc #ad |
| Part Number | Pw955 |
More information #ad
